Tuesday, 2 August 2016

Is the overheat of woodworking CNC Router motor a normal phenomenon?

Is the overheat of woodworking CNC Router motor a normal phenomenon?

           Detailed explanation as follows:

           Note: motor heating generally does not affect the life of the motor, for most customers do not have to worry too much. However, serious fever will bring some negative effects. If the thermal expansion coefficient of each part of the motor is different, the change of the structure stress and the tiny change of the internal air gap will affect the dynamic response of the motor. In some cases, there is no excessive heat, such as medical equipment and high precision testing equipment, etc.. So it is necessary to control the heating of the motor. When the motor temperature is too high, you can choose the CNC Router (
http://www.roc-tech.com/product/product34.html ) to stop, rest for a period of time to continue to work, you can also add the motor outside the heat sink to ensure that the heat of the motor in a timely manner.

           With the improvement of the performance and stability of the stepping motor, it is widely used in some motion controller. Its application in woodworking CNC Router industry is the most. Due to its internal structure is composed of iron core and windings, so it in a power on state will produce a certain quantity of heat, work for a long time, even a bit hot. To what extent the motor is normal, how to reduce the heat generated by the motor? Here we have a simple solution.

           The temperature range of motor heating mainly depends on the insulation level of the motor. Under normal circumstances, the internal insulation performance at high temperature (above 130 degrees) will be destroyed. So as long as the internal no more than 130 degrees, the motor will not be damaged, and then the surface temperature will be below 90 degrees. Therefore, the stepper motor surface temperature in 70-80 degrees are normal. Simple method of temperature measurement point to the usefulness of the temperature meter, also can judge roughly: by hand can touch more than 1-2 seconds, no more than 60 degrees; hand can touch, about 70-80 degrees; a few drops of water dripping rapidly gasification, 90 degrees above the.



Tuesday, 26 July 2016

The correct use of woodworking CNC Router tool

The correct use of woodworking CNC Router tool

           1. Jacket size should be appropriate, section, is not a circle, wear and hole taper clamping sleeve must not choose, otherwise it will lead to handle vibration, carving out the ideal effect.

           2. The handle to clamp sleeve contact moderate, hilt must firmly into the clip sleeve and tighten, if clamping sleeve used for a long time the hole deformation must immediately replaced jacket.

           3. Tool often checker toughness. If you are using a blunt, please immediately replaced, if continue to use not only carving effect will occur broken knife.

           4, The use of woodworking CNC Router ( 
http://www.roc-tech.com/product/product33.html ) to be imposed, the thickness of the process can not be more than the thickness of the cutting edge can be responsible for the knife will continue to appear.

           5. Different materials of the cutting, the use of cutting speed should be reasonable.

           6. Body, clothes, hair should not be close to the work of the object.

           7. Cutting recommended speed to maintain a balanced speed as consistent as possible, in order to achieve a better effect, cutting too long not to stay, to form a coherent whole.

           8. Tool to use a special cleaning agent to remove dirt.

           9. Butter can prevent the tool from rust.

           10. Tool can not be their own to polish or change the shape. 



Sunday, 17 July 2016

Types of motor failure problems of stone CNC Router

Types of motor failure problems of stone CNC Router

           Stone CNC Router, the machine believe many contact carving knife, carving machine industry personnel are aware of, here we can not be introduced, this article mainly stone CNC Router motor fault types, and how to solve an introduction.

           The first case is the stone CNC Router ( 
http://www.roc-tech.com/product/product35.html ) motor appears to reverse the situation. Staff need to check the motor line, because this situation is generally lack of phase of the motor line, you can also directly to the output UVW terminal exchange.

           The second case is the stone CNC Router motor operation when there is noise. Appear this kind of circumstance are generally stone CNC Router motor internal failures, this situation must send producers there repair or replacement; if it is a stone CNC Router motor overload, then to adjust speed.

           Third, stone CNC Router motor speed is very slow. This is the stone carving machine motor power problems, we are generally the first to check the cable to connect the stone CNC Router, check whether there is a short-circuit, may check the motor shortage phase.

           In the fourth case, the motor of the stone CNC Router is hot. This kind of situation, the problem is the stone carving machine cooling system, we generally through the inspection of the pump is working, and circulating water there is no cooling lowest level this two kinds of methods to carry out.

           Stone CNC Router motor fault types and the solution of the solution almost on the four, if the users have also found other types, you can contact us for a discussion. 


Tuesday, 12 July 2016

How to deal with the problem of increased voice of CNC Router?

How to deal with the problem of increased voice of CNC Router?

           In the normal use of the process of CNC Router ( http://www.roc-tech.com/product/product29.html ), if you find the CNC Router running sound bigger than before, this time we need to pay attention to the. Because the sound increases may mean a failure of a certain part of the machine. According to the use of the machine, the general sound of the parts of the increase is nothing more than a few places: the rotation of the spindle motor, rack and pinion gear meshing, sliding and the friction of the guide rail.

           After an abnormal sound, first look at the sound in general which is caused by. Spindle exception is relatively good judgment, as long as the opening of the spindle can be heard. This kind of problem is mostly the noise of the spindle bearing wear. The sound of it will be more and more serious because of the degree of wear and tear, and finally need to replace the new bearing. If it is a rack and pinion meshing problem, it is best to add some butter running back and forth several times, general this problem most is because machine daily maintenance caused by not timely, serious need to replace relief carving machine gear shaft. The slider appears to be a headache, it is generally difficult to determine the specific which is broken, we can according to the scratches on the track to judge. 


Tuesday, 5 July 2016

Entry-level tips for the operations of CNC Router

Entry-level tips for the operations of CNC Router

           Before working with the advertising CNC Router (http://www.roc-tech.com/product/product30.html ), we should check the spelling of the text part of the advertising CNC Router (http://www.roc-tech.com/product/product30.html ). If possible, print out and confirm with the customer.

           Again, in order to avoid these problems, we can try the following operation:

           1, check the engraving used pliers or a clamping head is wrong? At the same time, woodworking CNC Router ( 
http://www.roc-tech.com/product/product30.html ) pliers or a clamping head wear will lead to the misalignment are carvings. The pliers head or card if too tight, the knife head contacts are carvings moment will lead to be carving popup

           2, for those irregular shape of the sculpture, the surface seems to have been fixed very tight, when subjected to under the pressure will shake before and after. At this point, you can try to pad some of the waste material under the object to increase friction. Also is retained items comes with the package, while the objects are irregular in shape, but to their own packaging may is very regular and easy to be fixed, plus a small band, irregularly shaped objects can easily be fixed. Or try to fix the site of its rules, JT2-0ZU and discard its irregular parts.

           3, carved suffered under pressure if large, considering about whether you should use conical cutter nose, if CNC Router ( 
http://www.roc-tech.com/product/product30.html ) diamond cutter head in the process of carving mobile when pressure is too large, tool side, the pressure will be caused by carved objects move. If an incorrect diamond knife is used, it will lead to the same problem. A diamond knife with a 90 or 100 degree will be deep into the material, and the material will be moved in the process of engraving.

           4, due to woodworking CNC Router ( 
http://www.roc-tech.com/product/product30.html ) are often equipped with multifunctional pliers or a clamping head. And they are made of iron, so easy to carved caused by injury or the slide in the carving process, then choose some rubber cap or rubber tube for carved objects fixed will help.

           5, for carving plastic pattern can be reposted tape on the back are carvings, then taped to the side spray liquid glue, then affixed to a void on the surface, which can avoid the use of double-sided adhesive, and left to clean the surface. Because the tape stripping and cleaning easier. Advertising CNC Router ( 
http://www.roc-tech.com/product/product30.html ) using special carved tape, the tape side than on the other side of the viscous strong, so the plate can move freely or replaced. 



Saturday, 2 July 2016

How to reduce the heat of the motor of woodworking CNC Router

How to reduce the heat of the motor of woodworking CNC Router


We all know that the CNC Router (http://www.roc-tech.com/product/product67.html ) work for a long time will work longer if the fever is sometimes even some hot. To what extent the motor is normal, how to reduce the heat generated by the motor, the following CNC Router (http://www.roc-tech.com/product/product67.html ) manufacturer Wei Ting CNC to introduce you to the next.

           The temperature range of motor heating mainly depends on the insulation level of the motor. Under normal circumstances, the internal insulation performance at high temperature (above 130 degrees) will be destroyed. So as long as the internal no more than 130 degrees, the motor will not be damaged, and then the surface temperature will be below 90 degrees. Therefore, the stepper motor surface temperature in 70-80 degrees are normal. 

          Simple method of temperature measurement point to the usefulness of the temperature meter, also can judge roughly: by hand can touch more than 1 - 2 seconds, no more than 60 degrees; hand can touch, about 70 - 80 degrees; a few drops of water to a rapid gasification, 90 degrees above the. Motor heating in general will not affect the life of the motor, for most customers do not have to worry too much. However, serious fever will bring some negative effects. If the thermal expansion coefficient of each part of the motor is different, the change of the structure stress and the tiny change of the internal air gap will affect the dynamic response of the motor. In some cases, there is no excessive heat, such as medical equipment and high precision testing equipment, etc.. 

          So it is necessary to control the heating of the motor. When the motor temperature is too high, you can choose the CNC Router (http://www.roc-tech.com/product/product67.html ) to stop, rest for a period of time to continue to work, you can also add the motor outside the heat sink to ensure that the heat of the motor in a timely manner. 



Monday, 27 June 2016

Parts required to be protected in use of the woodworking CNC Router

Parts required to be protected in use of the woodworking CNC Router

           Woodworking CNC Router (http://www.roc-tech.com/product/product31.html) in use, must pay attention to protection, in particular, some parts, so as to make woodworking CNC Router (http://www.roc-tech.com/product/product31.html) to maintain good condition.

           1. woodworking CNC Router (http://www.roc-tech.com/product/product31.html) card head: motor between the head and the cutting tool is the friction between the metal fixed, so when installing the tool must be lubricated with oil, to prevent the long time does not remove or coolant corrosion caused by demolition difficult.

           2. woodworking CNC Router (http://www.roc-tech.com/product/product31.html) spindle motor protection: if woodworking CNC Router (http://www.roc-tech.com/product/product31.html) motor stop or motor speed is not uniform, please immediately cut off the power supply and contact the dealer maintenance. In the case of the motor stopped, woodworking CNC Router (http://www.roc-tech.com/product/product31.html) motor is not power, or the motor coil will burn, please use the woodworking CNC Router (http://www.roc-tech.com/product/product31.html) must pay attention to.

           3. every time after you are finished using woodworking CNC Router (http://www.roc-tech.com/product/product31.html), be sure to clean the machine, add oil on the guide rail, lest machine by environmental corrosion.